Gigabit Multimode Media Converter - HCL-GIGA-SX-SC
The multimode media converter is designed to provide a simple and cost effective means of conversion between copper (1000Base-T) and fiber optic (1000Base-SX/LX) media on Ethernet/Fast Ethernet networks.
Model Description
| Model | Connector Type |
| TP - SC | RJ45 (1000T) - SC 850/1310/1550nm |
| 1000Mbps Fiber Transceiver: |
| SC 1. multi-mode 220m 2 single-mode 10/20Km |
Packaging Contents Hardware Setup 
| Note: |
| 1. The media converter can be used either as a stand-alone unit
or as a slide-in unit. 2. For the TP port: a. Use straight-through RJ45 Ethernet cable. b. The cable pin-outs for the RJ45 jack are: 1,2,3,6,4,5,7,8 to 1,2,3,6,4,5,7,8. |
Panel Views and Descriptions
| LED | Status | Indication |
| PWR | On | Power is supplied to the device. |
| Off | No power is supplied to the device. |
|
| FX LINK | On | Fiber link is connected to the media converter. |
| Off | No fiber link connected to the media converter. |
|
| ACT | Blinking | A device is transmitting or receiving data in the network. |
| TPLINK100 | On | A 100Mbps device is connected to the TP port. |
| TPLINK1000 | On | A 1000Mbps device is connected to the TP port. |
| Port | Description |
| TP Port (1000TX) | 1. 1000Mbps 2. Auto-negotiation for Nway TP partner 3. Use RJ45 cable to connect to PC or switch |
| Fiber Ports (1000FX) |
1. 1000Mbps 2. Mode Selectable - Auto ON (Default) 3. Use fiber cable with appropriate connector to connect these ports to another converter or switch |
| Note: |
| The fiber link partners should be set at the same duplex mode. |
Cable Connection Parameters1000Base-X network allows 512-bit time delay between any two
node stations in a collision domain. The overall bit-time of TP/Fiber
wires and devices must be within 512 bit in a segment.You may use a
switch to break up collision domain and extend the cabling distance.
Below are the different cable limitations to consider:
1. TP (Cat. 5) Cable: 100m
2. Multi-mode Converter Fiber Cable:
| SC/LC Multi-Mode Converter Models: | |
| Multi-mode 62.5/125um, 850nm |
Node to Node: 220m Node to Switch: 220m |
| Multi-mode 50/125um, 850nm |
Node to Node: 550m Node to Switch: 550m |
2. Single -mode Converter Fiber Cable:
| SC Single-Mode Converter Optional Models: | |
| SC 1310nm |
Node to Node: 10/20/40km Node to Switch: 10/20/40km |
| SC 1550nm |
Node to Node: 40/60/80/100/120km Node to Switch: 40/60/80/100/120km |
Technical Specifications| Standard | IEEE 802.3ab 1000Base-T IEEE 802.3z 1000Base-SX/LX |
| TP cable | Cat. 5 (up to 100m) |
| TP connector | RJ45 |
| Fiber connector | SC |
| Fiber type | Single-mode (9/125um) Multi-mode (50/125, 62.5/125um) |
| Flow Control | IEEE 802.3x compliance (Fullduplex) Back pressure flow control (Halfduplex) |
| Data Transfer Rate | 1000Mps: 1 488 000 PPS 100Mps: 148 800 PPS |
| LED Indicators | PWR FX LINK ACT TPLINK1000 TPLINK100 |
| Power | 85 ~ 265VAC, 50/60Hz or 48VDC |
| Ambient temperature | 0°~70°C |
| Humidity | 5% ~ 90%, non-condensing |
| Dimensions | 135mm x 85mm x 26mm (LxWxH) |
| Note: |
| If you are connecting the media converter to a router or to a switch, please refer to the technical manual of your device. |
For business enquiries contact us at: webhost@hcl.in